隨著現代化的發展，自動焊接技術得到了更好的應用，在使用數控焊接設備時也要小心注意，以防造成人身傷害。接下來咱們就講講山東數控焊接設備在操作中需要注意的問題。

With the development of modernization, automatic welding technology has been better applied. When using numerical control welding equipment, care should be taken to prevent personal injury. Next, we will talk about the problems that need attention in the operation of Shandong CNC welding equipment.

(1)為確保機械設備不發生事故，不僅機械設備本身應該滿足要求，更重要的是要求操作人員嚴格遵守操作規程。當然，機械設備的操作規則因其類型而異，但它們的基本規則是相同的。

(1) In order to ensure that the mechanical equipment does not have accidents, not only the mechanical equipment itself should meet the safety requirements, but also the operators should strictly abide by the safety operation procedures. Of course, the safety operation rules of mechanical equipment vary according to their types, but their basic safety rules are the same.

(2)應該正確穿戴個人防護設備和用具。要求穿的一定要穿，不能穿的一定不要穿。例如，當操作旋轉加工時，婦女被要求戴帽子。如果她們不戴帽子，頭發可能會被卷起來。同時，要求不要戴手套。因為如果它們被磨損，機器的旋轉部分可能會擰入手套并傷害手。

(2) Personal protective equipment and appliances should be properly worn. What you are required to wear must be worn, and what you cannot wear must not be worn. For example, when operating rotary processing, women are required to wear hats. If they don't wear hats, their hair may curl up. At the same time, it is required not to wear gloves. Because if they are worn, the rotating part of the machine may screw into the gloves and hurt hands.

(3)作業前，應對機械設備進行檢查，并應空車運轉一下。只有確認正常后才能投入運行。

(3) Before operation, the mechanical equipment shall be inspected for safety and shall be operated without load. It can be put into operation only after it is confirmed to be normal.

(4)嚴禁操作有故障的機械設備。為了防止事故，禁止勉強應付。

(4) It is strictly forbidden to operate mechanical equipment with faults. In order to prevent accidents, forced coping is prohibited.

(5)機械設備的裝置應該按規定正確使用，不允許折疊使用。

(5) The safety devices of mechanical equipment shall be used correctly according to regulations, and folding is not allowed.

(6)機械設備中使用的支柱、夾具和加工件應該安裝牢固，不得松動。

(6) The props, clamps and machined parts used in mechanical equipment shall be firmly installed without looseness.

(7)機械設備運行時，禁止手動調節，不得用手測量零件，也不得光滑、清潔雜物等。如有必要，關閉機械設備。

(7) When the mechanical equipment is running, it is prohibited to adjust it manually, measure the parts by hand, or smooth or clean sundries. If necessary, first turn off the mechanical equipment.

(8)機械設備運行時，操作人員不得擅離崗位，以防出現問題，無人處理。

(8) During the operation of mechanical equipment, operators shall not leave their posts without permission to prevent problems from being handled by nobody.

(9)工作結束后，切斷電源，將車刀和工件撤出工作位置，整理好工作場地，擺放好零件和夾具，清理好機械設備的衛生。

(9) After the work is completed, cut off the power supply, remove the turning tool and workpiece from the working position, tidy up the work site, place the parts and fixtures, and clean up the sanitation of mechanical equipment.

以上就是數控焊接設備應用時需要注意的一些問題，關注好這些問題，不僅可以提高工作效率，而且在一定程度上可以保證人身，是對企業負責更是對自己負責。更多相關內容就來我們網站http://www.oimhc.com進行咨詢！

The above are some problems that should be paid attention to in the application of numerical control welding equipment. Paying attention to these problems can not only improve work efficiency, but also ensure personal safety to a certain extent. It is responsible for the enterprise as well as for itself. More relevant content will come to our website http://www.oimhc.com Consult!