The function of automatic welding robot is very advantageous. Have you paid attention to it? Ordinary welding equipment is completely controlled by manual experience. Therefore, if the welding point of the nut is high or low, and the stability of the output and power supply of the device is not ideal, false welding is easy to occur. In order to avoid similar phenomena, on the one hand, the solder joint is required to be stable, on the other hand, the power supply and transportation are required to be stable.

這時候，自動按揭機器人的優勢就顯現出來了，因為自動管道焊接機器人可以做到這一點。您可以根據不同材料和厚度的焊接工件的電流和電壓來調整焊接速度，以找到合適的焊接參數，從而減少出現焊接缺陷的可能性。

At this time, the advantages of automatic pipe welding robot appear, because automatic pipe welding robot can do this. You can adjust the welding speed according to the current and voltage of welding workpieces with different materials and thicknesses to find the appropriate welding parameters, so as to reduce the possibility of welding defects.

除了用自動管道焊接機器人代替設備外，焊接螺母之前的準備工作也非常重要。由于焊接件是由鋁制成的，并且鋁表面上有氧化膜，因此在焊接之前要清潔氧化膜。

In addition to replacing the equipment with automatic pipeline welding robot, the preparation before welding nuts is also very important. Since the weldment is made of aluminum and there is an oxide film on the aluminum surface, the oxide film shall be cleaned before welding.

清潔或腌制。然后在清潔氧化膜后的三個小時內使用焊接機器人進行焊接;否則，由于空氣中的氧化會產生新的氧化膜，這會影響焊接的實際質量。

Clean or pickle. Then, the welding robot is used for welding within three hours after cleaning the oxide film; Otherwise, new oxide film will be produced due to oxidation in the air, which will affect the actual quality of welding.

當自動管道焊接機器人使用不熔化的氬弧焊時，產生的電弧在不熔化的電極和工件之間燃燒，并且不與金屬發生化學反應的惰性氣體在周圍流動。的電弧形成保護蓋。即，此時自動管焊接機器人可以使鎢，電弧和熔池的端部不與熱影響區相鄰的高溫金屬接觸。從而有用防止氧化和吸收。

When the automatic pipe welding robot uses non melting argon arc welding, the generated arc burns between the non melting electrode and the workpiece, and the inert gas that does not react with the metal flows around. The arc forms a protective cover. That is, at this time, the automatic pipe welding robot can prevent the ends of tungsten, arc and molten pool from contacting the high-temperature metal adjacent to the heat affected zone. Thus, it is useful to prevent oxidation and absorption.

有害氣體，從而形成致密的焊接接頭。而且它顯示出更好的機械性能。

Harmful gases to form dense welded joints. And it shows better mechanical properties.

當自動管道焊接機器人通過氬弧焊進行焊接時，焊絲將穿過焊絲輪，導電噴嘴將導電，從而在基材和焊絲之間產生電弧。焊接，熔化焊絲和基礎材料并使用慣性。

When the automatic pipeline welding robot carries out welding through argon arc welding, the welding wire will pass through the welding wire wheel, and the conductive nozzle will conduct electricity, so as to generate an arc between the substrate and the welding wire. Weld, melt welding wires and base materials and use inertia.